Swimming pools have become an intrinsic part in the lives of a large number of people in the US. Apart from being a stellar form of exercise, swimming is an activity which can help you to unwind after a tiring day at work. In layman’s words, comfortable swimming is impossible without a functional swimming pool. Today, swimming pools are not just a place of luxury, but an integral part of people’s lives. If you own a swimming coaching center or a hotel where the pool plays a major role, then you should be aware of the fact, that pools require regular maintenance.
Exposure to chemicals and various kinds of elements will eat away the pool’s surface. Therefore, it is extremely important to resurface your pool every 8 to 10 years, in order to keep it in top-notch condition. Pool construction companies can assist you with any construction activity pertaining to your swimming pool. Typically, these are some of the important steps which should be followed in order to resurface your pool.
- Before you decide to resurface your pool, you should ensure whether you can afford the expenses or not. Typically, the average resurfacing project costs around $6 per square foot.
- Start by clearing and removing all the electronics and patio furniture from the pool area and store them in a separate place. Stripping a swimming pool will usually spread a lot of debris. If you are not careful, then you could destroy more delicate items.
- Tape a few weather-resistant drop cloths or a few tarps around the perimeter of the entire pool.
- Access your pool’s central pump system and switch it over to “backwash” or “drain” setting. You can also use submersible pump to cycle the water out of the pool. Remember, that resurfacing activity cannot begin until you have completely emptied the pool.
- Check the inside of the pool for any signs of cracks, blistering, crumbling and other form of deterioration. These signs are indications that your pool might require immediate resurfacing.
- Clean the surface of the pool. Use your hand to collect larger bits of debris like leaves, twigs and stones. After that, use pressure wash to remove mineral deposits, stubborn stains, chemicals and algae. Keep in mind that even the smallest pieces of dusts can ruin the surface material’s ability to install properly.
- Start striping the existing materials. Fiberglass, composite and plaster finishes will have to be chiseled away or sandblasted. Try to focus on one small area of the pool’s surface and gently move the nozzle of the sandblaster up and down in order to completely eat away the liner. Depending upon the size of your pool, the stripping process will take 1-3 days to complete.
- With the help of a wet/dry vacuum, carefully suction up all the dusts and debris which are formed around the pool area. Cleanup can be a daunting task and may add some extra days to the timeline of your projects.
- Select a time-frame when the weather condition is most favorable, for the materials which you have decided to work with. For example, epoxy paints, fiberglass and concrete-like materials set rapidly in dry and warm weather.
- Today, pool owners have got a wider range of options available to choose from. In case of small or standard sized pools, a simple fiberglass finish or a plaster is a pragmatic choice because they are easily available and are not difficult to install. If you are on a tight budget, then they are the most affordable options to opt for. But remember that plasters are not as durable as composite or synthetic materials, so it might require frequent replacement.
- Sophisticated and high-end pools offer impressive appearances when materials like pebbles, quartz, concrete and ceramic tiles are used for resurfacing purpose.
- Use a pool specific epoxy primer and roll on from one end of the pool to the other. Once the primer is dry, apply 3-4 coats of topcoat epoxy. Ensure that you sand the epoxy lightly between the coats. Typically, it will take around 2-3 hours of drying time for each coat, but it can also take longer time depending upon the climate of your region.
- Mix the dry plaster materials with water in a large tub until the point when it reaches a smooth and thick consistency. With the help of a trowel properly spread the plaster evenly and avoid any gaps in-between.
- Use a paint roller or sprayer to cover the walls and floor of the swimming pool with fiberglass. After that, spray a coat of resin over the top, then roll and sand the layers to make them smooth. Keep in mind that fiberglass sticks to whatever it touches, so ensure that you wear an old cloth.
- Give sufficient time to the new surface to dry. Irrespective of the material which you decide to use, it will take a lot of time to set up. Temperamental materials like fiberglass and plasters will typically require several days to dry completely. On the other hand epoxy paint will dry in a matter of few hours only.
- Properly inspect the pool inside and out. Ensure that the plumbing fixtures and lighting elements are properly installed, before you start to add water into the pool. This is your final opportunity to take care of last minute details like touching-up any spot which you may have missed. If you discover any visible holes, exposed concretes or cracks, then do not fill the swimming pool, as it might lead to highly expensive repairs. Also ensure that all the wirings under the pool are properly installed, as it can become a potential safety concern for the swimmers.
- Refill the pool with fresh water. Do not forget to add the requisite proportions of chlorine. This will help to keep bacteria and viruses at bay.
Today, there are a plethora of swimming pool contractors available in the market. However, rely on the ones which have persistently provided value for money services to their clients. Touch Of Art Construction Inc is one of the highly-rated companies which provide impeccable level of services to their clients. To learn more, visit http://www.touchofartlandscape.com or call 818-726-0613.
Touch Of Art Construction Inc. 